ironmanandy
03-27-2011, 10:02 PM
Call Andy with questions: 704 796 3502 located in Hayesville, NC 28904
I have had this jeep for over a year now here at Ironman4x4fab.com and have just slowly taken my time to use it for product design and measurements. In the process I have ended up with a very well built front suspension setup and many hours of labor that would cost loads more than I am asking for the jeep. It has not been off road since I acquired and began building.
This is the super rare Split window 2 door model that they only made a few of from late 80s into early 90s. The Cherokee has the venerable renix 4.0 FI engine with a 5 speed manual trans.
Here are some specs of the mods done here at Ironman:
6-7 " lift
-35" feirce tires on 17" incubus off road wheels
-skyjacker rear leafs
-AA SYE kit and custom rear drive shaft
-Complete custom front suspension:
-RE front coils/ 2" poly spacers,
-Ironman extra length long arm system (39)" ete +/- welded to frame allowing for stock cross member with laser cut 100A parts.
-Long arms made from 2"x.281 wall DOM with 1.5 threading 6" long for unmatched adjustment. Genuine Currie johnny joints used at frame.
-UCA's are Ironman4x4fab extreme duty uppers with 95 D poly for excellent torsion retension on front axle.
-UCA mounts on axle replaced with Ironman4x4fab.com Poly bushing kit with 95D poly and 1/2" grade 8 hardware.
-Drag link and tie rod machined from 1.25 CR solid with 3/4 16 L/R ends on all ends. 3/4 heims on pass side with adapter setup for high steering.
-Custom Iroman4x4fab.com track bar with double shear bracket modded to match all steering angles.
-RE front shocks.
-New brake rotors and vacuum system extened.
-stainless front brake lines
-locked front differential
-Longer front drive shaft removed for driver comfort as front axle is locked. Drive shaft is included with vehicle. Simple 8 bolt installation required for off-roading.
-Custom front bumper.
200000+ miles on vehicle but trans and t case have been replaced but mileage unknown.
-All added front suspension components are New
OME steering dampener to be installed
I am asking 4900.00 for this jeep I will also consider partial trades for stock Cherokees Grand Cherokees or Comanches, 2 or 4 wheel drive.
The asking price of the vehicle is based on the value of the wheels/tires, and suspension/ drive train work/components and labor involved.
Title in hand.
http://www.nc4x4.com/forums/attachment.php?attachmentid=35524&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35525&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35526&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35527&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35528&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35529&stc=1&d=1301279602
I have had this jeep for over a year now here at Ironman4x4fab.com and have just slowly taken my time to use it for product design and measurements. In the process I have ended up with a very well built front suspension setup and many hours of labor that would cost loads more than I am asking for the jeep. It has not been off road since I acquired and began building.
This is the super rare Split window 2 door model that they only made a few of from late 80s into early 90s. The Cherokee has the venerable renix 4.0 FI engine with a 5 speed manual trans.
Here are some specs of the mods done here at Ironman:
6-7 " lift
-35" feirce tires on 17" incubus off road wheels
-skyjacker rear leafs
-AA SYE kit and custom rear drive shaft
-Complete custom front suspension:
-RE front coils/ 2" poly spacers,
-Ironman extra length long arm system (39)" ete +/- welded to frame allowing for stock cross member with laser cut 100A parts.
-Long arms made from 2"x.281 wall DOM with 1.5 threading 6" long for unmatched adjustment. Genuine Currie johnny joints used at frame.
-UCA's are Ironman4x4fab extreme duty uppers with 95 D poly for excellent torsion retension on front axle.
-UCA mounts on axle replaced with Ironman4x4fab.com Poly bushing kit with 95D poly and 1/2" grade 8 hardware.
-Drag link and tie rod machined from 1.25 CR solid with 3/4 16 L/R ends on all ends. 3/4 heims on pass side with adapter setup for high steering.
-Custom Iroman4x4fab.com track bar with double shear bracket modded to match all steering angles.
-RE front shocks.
-New brake rotors and vacuum system extened.
-stainless front brake lines
-locked front differential
-Longer front drive shaft removed for driver comfort as front axle is locked. Drive shaft is included with vehicle. Simple 8 bolt installation required for off-roading.
-Custom front bumper.
200000+ miles on vehicle but trans and t case have been replaced but mileage unknown.
-All added front suspension components are New
OME steering dampener to be installed
I am asking 4900.00 for this jeep I will also consider partial trades for stock Cherokees Grand Cherokees or Comanches, 2 or 4 wheel drive.
The asking price of the vehicle is based on the value of the wheels/tires, and suspension/ drive train work/components and labor involved.
Title in hand.
http://www.nc4x4.com/forums/attachment.php?attachmentid=35524&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35525&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35526&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35527&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35528&stc=1&d=1301279602
http://www.nc4x4.com/forums/attachment.php?attachmentid=35529&stc=1&d=1301279602