PDA

View Full Version : Sad sight


BrianXJ
02-15-2011, 01:48 PM
This is what I have been looking at for the last two days and all day today.
http://i1188.photobucket.com/albums/z418/BrianXJ/CIMG0122.jpg
bluedragon436
02-15-2011, 01:49 PM
Well hurry up and fix that thing... and get her lifted!! LOL... Did today work out any better than the last two days on getting her back on the road??
BrianXJ
02-15-2011, 01:51 PM
Well hurry up and fix that thing... and get her lifted!! LOL... Did today work out any better than the last two days on getting her back on the road??

Well I had to get another pan gasket the one I had split on my install yesterday so they just delivered it so I am going to RTV it in place on the block before I put the pan up
prerunner1982
02-15-2011, 01:57 PM
I just replaced the Oil pan gasket on my 93 last month.. fun stuff but could have been worse. I found that if I put a bolt at each corner of the pan with the gasket on the pan that it held it in place well enough to get the pan positioned under the engine. I could then unbolt it and bolt the whole thing straight up onto the engine.
bluedragon436
02-15-2011, 01:58 PM
So you figured out that was where it was leaking was just the pan gasket?? I mean a leak is a leak, I know... but at least it wasn't the rear seal again..
rugidone
02-15-2011, 02:02 PM
Why does it look so warm outside in your picture :(
modestmar00xj
02-15-2011, 02:02 PM
hmm yeah lets get this thing trailing!
BrianXJ
02-15-2011, 02:24 PM
Why does it look so warm outside in your picture :(

The weather channel says 60. But the wind is blowing just a little.
TeXJ
02-15-2011, 03:15 PM
did you get the fel-pro one piece gasket?
Tural
02-15-2011, 03:24 PM
i know how to fix that sight.
throw it in my front yard, i'll take care of the rest. lol...
bigjim350
02-15-2011, 06:14 PM
Not really a sad sight. EVERY Jeep looks like that sooner or later.
BrianXJ
02-16-2011, 01:35 AM
i know how to fix that sight.
throw it in my front yard, i'll take care of the rest. lol...


Trust me you dont want this one lol
Mudderoy
02-16-2011, 02:17 AM
Nothing there would be even sadder.
Tural
02-16-2011, 05:30 AM
Trust me you dont want this one lol

it's all nuts and bolts man. many times it boils down to patience. you get tired of fixing it... lol...
BrianXJ
02-16-2011, 09:06 AM
it's all nuts and bolts man. many times it boils down to patience. you get tired of fixing it... lol...

Thats why I walked away and let it wait until I get up today to finish it lol
Tural
02-18-2011, 10:14 PM
let me give you my sad sight...
i have a ford 8.8 with 4.10s and lsd, dana 30 with 4.10s, c8.25 with 3.55s, zj backing plates, non abs proportioning valve and a bunch of other goodies sitting in the back yard and i have no time to work on em, to get my jeeps set up right.
BrianXJ
02-18-2011, 10:21 PM
Well hopefully it comes off the jackstands tomorrow. I got the oil pan on today and tomorrow I am tackling the trans cooler line leak. Then it is time to wheel!!!!!!!!!!
oderdene
02-18-2011, 10:41 PM
let me give you my sad sight...
i have a ford 8.8 with 4.10s and lsd, dana 30 with 4.10s, c8.25 with 3.55s, zj backing plates, non abs proportioning valve and a bunch of other goodies sitting in the back yard and i have no time to work on em, to get my jeeps set up right.

me too, huge plans, bunch of things; no time and cold enough :(