View Full Version : 2021 Jeep Talk Show Gladiator Skid System Install
Mudderoy
02-11-2024, 09:12 AM
For the last year, or so, I've been interested in getting a skid system for the Gladiator. I first started thinking about this when co-host Wendy put on an invite only off-road event in Big Bear Lake California.
Lockers, 35's and lift were required. One caviout was that if you were on 35's aftermarket skids where highly recommended.
I didn't get to go, but I also didn't have aftermarket skids. This started me looking at skids though. I have bumpers from Motobilt and I'm very impressed with the quality, so I checked out Motobilt.
Photo from Motobilt
14994
The smoothness and coverage hooked me. This past November, Black Friday, I bought it.
Shipping was fast! Less than I week!
14995
Two of the 4 piece skid system. I was taking a break from getting everything off the pallet.
14997
Mudderoy
02-11-2024, 09:32 AM
I've said it before and I'll say it again. It's easier to order than it is to install. The weight of the center skid was a chore to install but prepping and painting was far more work.
Center skid goes in with 4 bolts.
14998
14999
15000
4.3LXJ
02-12-2024, 12:01 PM
Looks nice and beefy. How much does that weigh?
Mudderoy
02-12-2024, 11:14 PM
I don't know. I asked one of the people that created it, he wasn't sure. Is this shipping weight, or skid plates weight?
https://motobilt.com/products/jeep-jt-gladiator-skid-system#specifications
? 3/16 inch steel construction.
? Large 4 piece design.
? 1 hour (estimated) install time.
? Recessed bolts that self center.
? Entire system is completely flush.
? Boat side design.
? Built in cross member.
? Large oil pan access panel.
? Notched ends so that a car lift can still be used for repairs.
? Individual skids can be removed for repairs and maintenance on your Jeep.
? Weight: 240lbs (approx.)
Benefits
? Steel construction for superior strength.
? 4 piece design allows for the most protection.
? Quick and easy install.
? Flush underside allows you to easily slide over obstacles.
? Built in crossmember adds strength and rigidity.
? Large oil pan access panel allows for clean and effortless oil changes.
? No drilling.
? No need to drop or empty your fuel tank.
Included
? Transmission / Transfer case skid plate
? Engine skid plate
? Fuel tank skid plate
? Exhaust skid plate
? Hardware
Ships raw steel. Will need to be painted or powder coated. We recommend test-fitting all Motobilt products before paint/powder coat.
Weight = 240 lbs
Mudderoy
02-13-2024, 08:08 AM
The upside down picture really confuses me. lol
15001
15002
15003
Mudderoy
02-13-2024, 08:12 AM
15004
15005
15006
15007
4.3LXJ
02-13-2024, 08:56 AM
Plenty of plate there. I have been thinking about that for the XJ. But I am thinking I want to save as much weight as possible and would have to fabricate it anyway since nothing is standard on it anymore. I have been daydreaming of something tubular instead of a plate
Mudderoy
02-13-2024, 09:23 AM
Good starter. I don't remember if you're on long arms are not.
15009
15008
https://ironman4x4fab.com/collections/suspension/products/xj-4-link-front-crossmember
4.3LXJ
02-13-2024, 09:24 AM
Yes, plated uniframe and three link long arm in front. In the process of linking the rear also
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.