F1Addict
09-03-2013, 03:35 PM
I decided it was time to replace the crappy factory screws holding the decorative rails to the roof with something better. I noticed, while rehabbing the mount rails that Jeep used rubber Well Nuts to attach them. I'm sure it was a cost issue but the decorative rails were attached using self-tapping screws and a dab of some sort of sticky stuff, presumably to prevent leaking? From the factory, they are attached using a screw and plastic collar that tends to disintegrate after several years of exposure to the elements. Sorry this isn't a more interesting project, just practicing my write-up skills for when I actually do something important
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8109_zps32c99b88.jpg
The obvious first step was to remove the rails. That revealed a nasty mess.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8111_zps372518ab.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8141_zps2a752453.jpg
I cleaned up the mess...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8116_zpsc0314a4b.jpg
Here are the things you'll need (besides (12) 5/16" Well Nuts, stainless button-head screws, and appropriate size nylon washers): Electric drill, pilot drill (smaller than 5/16ths), stepper drill, and masking tape.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8121_zps4819c69c.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8133_zpsc629e09c.jpg
Tape each of the holes to prevent metal shavings from damaging the paint. This step will likely be more important to some than others. My paint is in good shape so I didn't want to mess it up with spinning spirals of sheet metal.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8123_zpscf85b06d.jpg
Use the pilot drill to enlarge the hole. Make sure you control the drill so that you don't punch through something important (like your headliner) when it goes through. I used a vacuum to suck up the little bits.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8126_zpsdd63643d.jpg
Next, use the stepper drill to enlarge the hole to 5/16ths inch. I marked the drill with a Sharpee so I knew when to stop.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8128_zpsaf181023.jpg
I went slightly beyond 5/16ths creating a slight chamfer at the hole opening. This was the result.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8131_zps4d7863dd.jpg
Next, press in the Well Nut. It can be a bit difficult but the fit needs to be as tight as possible to prevent the nut from spinning in the hole when you tighten it and to keep water out when it's tight.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8134_zps80b0f46b.jpg
Well Nuts installed...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8139_zpsd1d384b4.jpg
Now, reinstall the stainless rails
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8155_zps79ef4d48.jpg
Here are some other pics of the finished project...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8171_zps67b2b27a.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8157_zps70932ccb.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8156_zps8f450f89.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8109_zps32c99b88.jpg
The obvious first step was to remove the rails. That revealed a nasty mess.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8111_zps372518ab.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8141_zps2a752453.jpg
I cleaned up the mess...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8116_zpsc0314a4b.jpg
Here are the things you'll need (besides (12) 5/16" Well Nuts, stainless button-head screws, and appropriate size nylon washers): Electric drill, pilot drill (smaller than 5/16ths), stepper drill, and masking tape.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8121_zps4819c69c.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8133_zpsc629e09c.jpg
Tape each of the holes to prevent metal shavings from damaging the paint. This step will likely be more important to some than others. My paint is in good shape so I didn't want to mess it up with spinning spirals of sheet metal.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8123_zpscf85b06d.jpg
Use the pilot drill to enlarge the hole. Make sure you control the drill so that you don't punch through something important (like your headliner) when it goes through. I used a vacuum to suck up the little bits.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8126_zpsdd63643d.jpg
Next, use the stepper drill to enlarge the hole to 5/16ths inch. I marked the drill with a Sharpee so I knew when to stop.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8128_zpsaf181023.jpg
I went slightly beyond 5/16ths creating a slight chamfer at the hole opening. This was the result.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8131_zps4d7863dd.jpg
Next, press in the Well Nut. It can be a bit difficult but the fit needs to be as tight as possible to prevent the nut from spinning in the hole when you tighten it and to keep water out when it's tight.
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8134_zps80b0f46b.jpg
Well Nuts installed...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8139_zpsd1d384b4.jpg
Now, reinstall the stainless rails
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8155_zps79ef4d48.jpg
Here are some other pics of the finished project...
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8171_zps67b2b27a.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8157_zps70932ccb.jpg
http://i140.photobucket.com/albums/r34/F1Addict/Jeep/IMG_8156_zps8f450f89.jpg